Duct Accessories

Product Details:

DESCRIPTION

Triplex duct plugs are split plugs for sealing around,

organizing, and supporting up to three sub ducts,

pipes, or cables. The plugs are designed for use in

round openings such as conduits, conduit fittings,

and core-drilled wall penetrations. Effective long term

water-tight and air-tight seals, these products

also prevent mud, backfill, and slurry from entering

handholes, manholes, and buildings during the

construction process.

Triplex Duct Plugs Features:-

Split design for retrofitting without disassembly

Anchor and organize sub ducts or multiple duct

systems Eliminate duct-edge abrasion to cables

Expandable gasket allows for expansion and

contraction of cables or sub ducts without

leakage Excellent for supporting cables at the tops of riser. 

Product Details:

DESCRIPTION

• High-impact plastic components, combined with

      durable elastic gaskets

• Corrosion proof and effective as long-term or

      temporary seals

• Water-tight and gas-tight

• Equipped with a rope tie device to allow the

      securing of pull rope to the plug's back

      compression plate

• Removable and reusable

Product Details:

Removable and reusable duct seal holds inner duct

securely and prevents migration. Easy installation

requires no foam or chemicals.

Product Details:

Sub Duct Anchor/Plug is made of suitably compounded 

rubber and it is designed to seal upto four sub ducts of

32mm inside 110 mm PVC pipe. Expansion of the anchor 

is achived by pressing the rubber between metallic washers. 

All metallic parts are manufactured from Galvanised Stel. 

Stainless Steel parts can be supplied on request.

Product Details:

Duct Spacers are made of Polypropylene or any other synthetic material as per requirement of the 

customers and are used for supporting PVC Pipes. These are Two Types i.e. Base Spacer and 

Intermediate Spacer . 

Features:- 

• Used to uniformly separate the 20MM & 32MM ducts in the Trench 

• Manufactured from Polypropylene / chemically resistant & Non-degradable 

• Inter-connectable to adjacent spacer. 

Base Spacer 

Cat No Type 

BS-20 20X8 (8 WAY) 

BS-20-1 20X5 (5 WAY) 

BS-32 32X4 (4 WAY) 

Intermediate Spacer 

Cat No Type 

IS-20 20X8 DOUBLE (16 WAY 

IS-20-1 20X5 DOUBLE (10 WAY) 

IS-32 32X4 DOUBLE (8 WAY)

Product Details:

 

ALUMINIUM DUCT SPACER FOR MICRO DUCTS

These duct spacers for micro ducts are made of Aluminum die casting &

supported by fully threaded steel rods & steel nuts. After

aluminum die casting the separators are machined to remove all

sharp edges & extra aluminum deposited during casting.

The construction of these spacers is such that there is a base

aluminum horizontal bar which is fixed with the threaded rod

with help of nuts. There are number of horizontal aluminum

separators which can be added depending on the requirements.

After installing the bundles of 12/8 mm & 25/20 mm micro ducts

between the horizontal separators the top separators is fixed

firmly with the help of nuts.

These aluminum duct spacer for micro duct are used for installing

bundles of plastic micro ducts of 12/8 mm & 25/20 mm dia in a

trench as mentioned in the table below.

 

 

Features:-

• Manufactured from Aluminum die casting.

• Easy to accommodate large number of micro ducts bundles as per the requirements.

• Easy to install

• Used to uniformly separate micro duct bundles of different sizes in the trench.

• These duct spacers for micro ducts are made of Aluminum die casting &
• supported by fully threaded steel rods & steel nuts. After
• aluminum die casting the separators are machined to remove all
• sharp edges & extra aluminum deposited during casting.
• The construction of these spacers is such that there is a base
• aluminum horizontal bar which is fixed with the threaded rod
• with help of nuts. There are number of horizontal aluminum
• separators which can be added depending on the requirements.
• After installing the bundles of 12/8 mm & 25/20 mm micro ducts
• between the horizontal separators the top separators is fixed
• firmly with the help of nuts.
• These aluminum duct spacer for micro duct are used for installing
• bundles of plastic micro ducts of 12/8 mm & 25/20 mm dia in 

• Cat No	Inside Width	Height	Micro Duct Type
  ALMD-Type -1	80 mm	140 mm	Bundles of 12/8 mm
  ALMD-Type-2	80 mm	340 mm	Bundles of 25/20 mm+12/8 mm

 

 

Features:-

• Manufactured from Aluminum die casting.

• Easy to accommodate large number of micro ducts bundles as per the requirements.

Product Details:

ALUMINIUM DUCT SPACER

These duct spacers are made of Aluminum die casting &

supported by fully threaded steel rods & steel nuts. After

aluminum die casting the separators are machined to remove all

sharp edges & extra aluminum deposited during casting.

The construction of these spacers is such that there is a base

aluminum horizontal bar which is fixed with the threaded rod

with help of nuts. There are number of horizontal aluminum
separators which can be added depending on the requirements.

After installing the pipes between the horizontal separatorsthe top separators is fixed firmly with the help of nuts.

These aluminum duct spacer are used for installing

plastic ducts of 20 mm & 32 mm dia in a trench asmentioned in the table below.

Features:-

• Manufactured from Aluminum die casting.

• Easy to accommodate large number of ducts as per the requirements.

• Easy to install

• Used to uniformly separate the 20 mm & 32 mm ducts in the Trench

Product Details:

Specifications:

• Used to seal the 4” / 110mm duct from entry of water
• Ducts inner diameter range: 99mm to 109mm
• Materials used: PVC & EPDM Rubber

Product Details:

The telephone network from telephone exchange Up to the customer’s premises need to be protected against water /sediments/unwanted objects etc. Our Sub-Ducts Anchor/Plugs are used for sealing cables and inner ducts in the telephones networks. These Sub-Duct Anchor/Plugs are made of suitability compounded rubber. Expansion of the Anchor/Plug is achieved by pressing the rubber between metallic washer. All metallic parts are manufactured from Galvanised steel. Stainless steel parts can be supplied on request. Following are the features of these Sub -Duct Anchor:
• Water Tight
• Simple to install
• Removable and reusable
• No special tools required for installation
• Protect cable from sharp corners at duct entry
• Can be installed in any type of duct

Product Details:

Specifications:

• Intermediate Spacer for Conduit Separation
• Dimension: 5 inch X 3 inch
• Material: Non-Metallic

Product Details:

Duct Plug is composed of two PVC rings and expandable rubber rings.It has a provision to attach the draw cord. Duct Plug mechanical device used to seal the duct from the entry of water.

Specifications:

• Cat No: DP-110
• Duct Size: 110 mm
• Material: Non metal

Product Details:

C’ Crimp Connectors are made from Electrolytic Copper and are

used in overhead line tapping, dead ending and earthing

applications.

Product Details:

Triplex Duct Plug are split plugs for sealing around, organizing, and supporting up to three subducts, pipes, or cables. The plugs are designed for use in round openings such as conduits, conduit fittings, and core-drilled wall penetrations.

Specifications:

• Nominal Inner Diameter: 1.0inch
• Range(inch): 0.98-1.02
• Range(mm): 24.89-25.91

Product Details:

Terminal Blocks

These are made of high conductivity Brass and available in Brass/Tin

plated color.

Product Details:

Material:-Malleable iron, zinc

Finish:-Galvanized, black enamel self (zinc)

 

Product Details:

Description:- Fiber Glass marker post manufactured by Advance Technologies is an above ground utility marker used for identifying and avoiding major costly repairs, interruption of utility services and/or injury to those around. These Fiber Glass marker post also be used as a Highway Delineators Boundary marker or Trail Markers. Salient Feature:- • Light Weight • High Visibility at night • Whether resistance • U.V.Resistence • Maintenance Free • Easy to install Construction:- The Fiberglass Marker Post are made from light weight, high Impact Fiberglass reinforced resins. This will provide maximum whether resistance against rot and rust from hot/cold or UV exposure. The fiber will also not cause irritation to eye and/ or skin. The unique design and material can take repeated flexing and abuse. The decals are manufactured from quality steel sheets with black lettering on yellow back ground and are fixed to the Fiber Glass marker post with blind revit.The marker post can be supplied with standard or custom decals, color & design. The Marker post & decals are designed & manufactured in accordance to figure 1. Reflective self adhesive tape bands are provided and wrapped around the post at suitable places for visibility at night. Figure 1 2 Installation:- Installation of Fiber Glass Marker post is very easy on most of the soil conditions & does not require special installation tools. The installation of these marker posts is fast & is inexpensive way to mark & protect the OSP network. The Fiber Glass Marker Post is generally placed in accordance with figure 2

Product Details:

We are providing the best quality of Blank Duct Plug to our customers.

Specifications:

• Nominal Size: 2mm
• Range: 1.83"-2.36"
• PN: WTP200

Product Details:

Made of high quality, flat, seamless annealed tinned copper. It is used for providing a common electrical bonding facility for all cables and joints in manholes or cable vaults. Cat No Description 

BR-01 Bonding Ribbon12 (W) x 1 (T) x 20 m (L)

Product Details:

We are dealing in a wide and best range of Neutral Links.

These are made of high conductivity Brass and available in Brass colour,

Tin plated and Nickel plated.

Product Details:

Earthing Blocks

These are made of Brass and are tin plated. These are available in sizes of 4 ways and 8 ways.